TurboChef
TurboChef - 101273 - 2 Pole Relay
part #101273
TurboChef - 101273 - 2 Pole Relay (C3D / BULLET / NGC / i5 / i3 / NGO / HHB / HHB2)
F3 Faults - Usually a sign one of your 2 pole relays are bad or faulty. There are a number of things that can cause your relay to be faulty. These include Waveguides, Magnetrons, HV Transformers, and Diodes. If your oven is flashing F3, it could be a blown 20A fuse (Part # 100599)
TurboChef - 102012 - Door Switch
part #102012
TurboChef - 102012 - Door Switch (C3D / NGC / i5 / i3 / NGO / HHB2)
F4 Faults are caused by the door switched being out of sequence. This can occasionally blow the 20A Fuse (100599). This fault can be caused by bent door switches (102012 or i1-3207) or faulty hinges.
NGC Left Hinge NGC-1572
NGC Right Hinge NGC-1573
HHB Hinge 102807
Encore / NGO Left Hinge ENC-3015-1
Encore / NGO Right Hinge ENC-3015-2
Turbochef - 102075 - Hi Limit Switch
part #102075
Turbochef - 102075 - Hi-Limit Switch - Item #102075
F8 Faults can be caused by a faulty Hi-Limit. If your Hi-Limit continually trips, it could be a faulty SSR (NGC-3005) causing the issue. Each time you have to reset your Hi-Limit it lowers the tolerance  , your heaters may stay on and keep heating even when the heat is off. It may keep heating until the Hi-Limit (102075) trips. The SSR may even burn out the IR Element (NGC-3003 or ENC-3002) if it gets hot enough.
TurboChef - HHB-8106 - Blower Motor Assembly
part #HHB-8106
TurboChef - HHB-8106 - Blower Motor Assembly (HHB / HHB2)
F1 Faults can be caused by a faulty blower or BMSC (CON-7013) in most cases.
TurboChef - NGC-3005 - Dual 40A Solid State Relay
part #NGC-3005
TurboChef - NGC-3005 - Dual 40A Solid State Relay (C3D / NGC / i5 / i3 / NGO / HHB / HHB2)
F8 Faults can be caused by a faulty SSR. If your SSR is sticking, your heaters may stay on and keep heating even when the heat is off. It may keep heating until the Hi-Limit (102075) trips. The SSR may even burn out the IR Element (NGC-3003 or ENC-3002) if it gets hot enough.
F2 faults mean the oven is not staying hot enough to cook food. On NGCs Usually it is a top wire that has burnt off, a heater on (NGC-3011 or NGC-3003) has gone bad or a SSR (NGC-3005) isn't operating properly. It can also occur if the door is left open for too long in between cook cycles or the white glass waveguide covers (NGC-3029) are cracked or broken inside the oven.
Â
TurboChef - 102086 - 120F Snap Disc Thermostat
part #102086
TurboChef - 102086 - 120F Snap Disc Thermostat
TurboChef - 102805 - Hinge, LEFT : (USE PART # NGC-1572)
part #102805
Part # 102805 has been replaced with Part # NGC-1572
TurboChef - 100592 - 12 Amp Fuse
part #100592
TurboChef - 100592 - 12 Amp Fuse (C3 / CD3 / NGC / i5 / i3 / NGO / HHB / HHB2)
TurboChef - NGC-3083 - Alternate Sound Device
part #NGC-3083
TurboChef - NGC-3083 - Alternate Sound Device (C3 / C3D / NGC / HHB / HHB2)
TurboChef - HHB-8244 - Keypad, HHB2, General Market
part #HHB-8244
Keypad, HHB2, General Market
TurboChef - HHB-3234 - Cooling Fan w/Self Tap Screws Service Kit
part #HHB-3234
TurboChef - HHB-3234 - Cooling Fan w/Self Tap Screws Service Kit (HHB / HHB2)
TurboChef - 100506 - Smart Card Reader
part #100506
TurboChef - 100506 - Smart Card Reader (C3D / NGC / NGO / HHB / HHB2 / HHC3240 / HHC2020)